| |
Machine Manager integration |
Gas flow angle defined on Machine Manager portal will show correct direction of the Gas flow on platform scenes only for values: 0, 90,180, 270 or 360 degrees. |
27.x |
| |
Machine Manager integration |
In rare cases, for rectangular platforms with rounded corners defined on Machine Manager - the platform won’t be visualized in Magics. |
27.x |
| |
Machine Manager integration |
Field overlaps that aren’t connected to two opposite sides of the platform won’t be visualized on the platform scene in Magics. |
27.x |
| 94765 |
BREP handling |
In specific cases, some edges causing failure of Fillet operation are not rendered in error state |
27.x |
| 1057809 |
BREP handling |
In some cases, a BREP Tensile bar primitive might have wrong orientation upon creation that can be adjusted manually afterwards. |
27.x |
| 1035475 |
BREP handling |
In some cases, filleting a convergent body might result in error. |
27.x |
| 1043380 |
CO-AM integration |
CO-AM part is considered as modified after Translate + Copy operation |
27.x |
| 985667 |
CO-AM integration |
Undo/Redo operations don’t change the state of "Save part to CO-AM" button |
27.x |
| 1061307 |
CO-AM integration |
Operations recorded for a specific part revision in CO-AM can include some positioning and supports changes from other parts |
27.x |
| |
Import & Export |
Missing CAD import(s) after Magics upgrade |
27.01, 27.02 |
| 908031 |
Import & Export |
In certain cases, no warning is shown asking the user to save a BREP part/ BREP part scene |
27.x |
| 965412 |
Import & Export |
Select orientation: when clicking close, all subsequent part loading is cancelled regardless of "Apply to all" state. |
27.x |
| 1059055 |
Import & Export |
Part selection can not be saved to matamx files |
27.x |
| 1036953 |
Import & Export |
Importing of files via MatConvert is not possible if the file path is longer than 256 characters. (MatConvert known issue) |
27.x |
| 1012231 |
Import & Export |
In rare cases, importing part on the platform can block ‘Select Orientation’ dialog resulting in an infinite Magics hang. As workaround, the ‘Select Orientation’ dialog should be disabled in Magics settings. |
27.x |
| 940866 |
Import & Export |
Unicode characters are not supported when exporting a BREP model to STEP |
27.x |
| 888940 |
Import & Export |
Concept of colours for BREP models is not fully supported yet, only face colours are being preserved upon import of a part. |
27.x |
| 964608 |
Import & Export |
File preview of Magics files containing BREP models is not shown. |
27.x |
| 1026937 |
Other |
Magics is not considering the concept of sRGB |
All |
| 1062133 |
Other |
After uninstallation, the uninstalled Magics version is still available in the Windows ‘open with’ list |
27.x |
| 1062425 |
Other |
No desktop icon/shortcut is created in case Magics is not installed in the default destination folder |
27.x |
| |
Other |
Titles of items in History are all called Database. |
27.x |
| |
Other |
Some of the default shortcuts and context menu are still missing. |
27.x |
| 1044967 |
Other |
Rapidfit command is not present in default UI profile however it can be launched from the quick search in the platform layout. |
27.x |
| |
Other |
In some cases, for Top/Bottom plane operation, ‘Indicate plane’ button should be re-activated to make it work after changing part selection. |
27.x |
| |
Other |
The name of original part is not restored after Undo of multiple operations. |
27.x |
| 1055765 |
Other |
The zone legend is missing in the ‘Check Slices Distribution’ graph |
27.x |
| 1063150 |
Other |
The point legend is missing in the ‘Compare Points’ graph under Simulation |
27.x |
| 1064544 |
Other |
Upon importing preferences from a another Magics installation (either via import settings, or upon launching a newly installed Magics version), Magics will also update the MatConvert version settings. This could cause Magics to use an older MatConvert that does not contain the latest compatibility or functionality needed to fully use Magics. For Magics 27 it is recommended to use MatConvert 10.4 or higher. This can be set in Settings > Modules > MatConvert |
all until Magics 27.02 |
| |
Support Generation |
Failure to save SG profile in Magics 27 |
27.0, 27.01 |
| |
Support Generation |
Disabling the showing of perforations in supports can lead to supports overlapping with a part. |
27.x |
| |
Support Generation |
Situations where a part that has a surface that is (partially) closer than 1mm to the platform and that is supported by trees with angling applied, can lead to incorrect tree supports being generated. |
27.x |
| |
Support Generation |
The ‘Trim supports on other parts’ functionality might not work as expected when used in combination with post-processing. |
27.x |
| |
Support Generation |
The ‘Trim supports on other parts’ functionality might not work as expected when used with tree supports and a part intersecting the tree supports is moved. |
27.x |
| |
Support Generation |
The ‘Trim supports on other parts’ functionality might not work as expected when moving the part on which support structures of another part rests. |
27.x |
| |
Support Generation |
When the creation of manual tree support is interrupted before the tree support is generated, an empty support surface can remain. This support surface can be removed manually. |
27.x |
| |
Support Generation |
In some cases where block support is used, the state of the parameter ‘GENERAL > Critical points > Local minima support > Adjust hatching’ can influence the state of the parameter ‘Add point support > Align with hatching’. |
27.x |
| |
Support Generation |
Modifying a support surface (e.g., adding or removing triangles) with Tree supports and using ‘regenerate’ button will not update the Tree supports with the modified surface. Changing to and from another support type or modifying a parameter will update the Tree supports with the modified surface. |
27.x |
| |
Support Generation |
Gusset supports may not be properly trimmed in certain cases. |
27.x |
| |
Support Generation |
In some cases, manually added supports are transferred with wrong position. |
27.x |
| |
Support Generation |
Thickened non-solid support may intersect or detach from the part or create open contours. |
27.x |
| |
Support Generation |
Manually created surfaces that contain overlapping projections may result in support structures being generated above the part. |
27.x |
| |
Support Generation |
Applying 2D Cut on a Block support with thickened border may result in alteration of the geometry on the border corners. |
27.x |
| |
Support Generation |
No-support zones on marked Structures (for some geometries of Structures) are ignored during e-stage generation. |
27.x |